Digital Video Forums

Go Back   Digital Video Forums > Disc Formats > DVD Blank Media, Burning, Recording Hardware

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
Old 14 Nov 2005, 04:04 AM   #1
Junior Member
Junior Member
 
Join Date: Nov 2005
Posts: 18
Exclamation Nero burn problem. please help

Hello, I have a problem when burning to dvd.

What I'm trying to do is burn Scarface anniversary edition to a blank dvd.

I've read and experienced that the latest version of Dvd shrink has problems with the encryption on the dvd. So I went ahead and used Magic Dvd ripper to rip the files from the dvd onto my hard drive. I then used Dvd shrink to compress the 7gig files back down to 4 gigs by going to "open files" and selecting the video_ts folder.

Once I got the files compressed, I used "Nero OEM suite" which came with my dvd burner. this is my burner. http://www.mdmm.com/products/optical...in1-16-8DL.asp

My problem is, when I go into nero and load the compressed files, I select the 4x burn speed (tried 8,12, and 16x also) and it starts the burn and a few seconds later, the dvd comes back out and says something about a reset error.

The blank dvds that I'm using is TDK dvd-r 16x 4.7gb. I've also tried it on a Sony dvd+rw 4x 4.7gb dvd and it worked fine. I don't think the TDK dvds are bad, becuase I used them to burn The bourne Identity with dvd shrink (no problem with protection so I used that) and nero on 16x speed with no problem.

I have updated the firmware for my dvd burner, and I also have "DMA if available" set for both my primary and secondary IDE controllers.

Also here is my log file from nero when trying to burn Scarface.

Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'D:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 9:35:32 AM
Nero Version: 6.6.0.8 (Nero Express)
Recorder: <MAD DOG MD-16XDVD9A4> Version: 1.F1 - HA 4 TA 0 - 6.6.0.8
Adapter driver: <> HA 4
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <MAD DOG MD-16XDVD9A4 >Version: 1.F1 - HA 4 TA 0 - 6.6.0.8
=== Scsi-Device-Map ===
CdRomPeripheral : TDK CDRW121032 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : TOSHIBA DVD-ROM SD-M1302 atapi Port 1 ID 1 DMA: On
CdRomPeripheral : SCSIVAX DVD/CD-ROM 2.7a Vax347s Port 2 ID 0 DMA: Off
DiskPeripheral : WDC WD2000JD-00GBB0 02.0 viamraid Port 3 ID 0 DMA: Off

=== CDRom-Device-Map ===
TDK CDRW121032 E: CDRom0
TOSHIBA DVD-ROM SD-M1302 F: CDRom1
SCSIVAX DVD/CD-ROM H: CDRom2
MAD DOG MD-16XDVD9A4 G: CDRom3
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1022MB (1047280kB)
Free physical memory: 619MB (634584kB)
Memory in use : 39 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

13.11.2005
UDF/ISO compilation
12:50:59 PM #1 Phase 112 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation started

12:50:59 PM #2 Phase 114 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation completed (no file modified)

12:50:59 PM #3 Text 0 File Isodoc.cpp, Line 6172
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet :FALSE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE

12:50:59 PM #4 Phase 111 File dlgbrnst.cpp, Line 1832
DVD-Video files sorted

12:50:59 PM #5 Text 0 File Reader.cpp, Line 127
Reader running

12:50:59 PM #6 Text 0 File Writer.cpp, Line 122
Writer MAD DOG MD-16XDVD9A4 running

12:50:59 PM #7 ISO9660GEN -11 File geniso.cpp, Line 3293
First writeable address = 0 (0x00000000)

12:50:59 PM #8 ISO9660GEN -11 File geniso.cpp, Line 3293
First writeable address = 0 (0x00000000)

12:50:59 PM #9 Text 0 File Burncd.cpp, Line 3153
Turn on Disc-At-Once, using DVD media

12:50:59 PM #10 Text 0 File DlgWaitCD.cpp, Line 259
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286127 (508:01.52, 4465MB)

12:50:59 PM #11 Text 0 File DlgWaitCD.cpp, Line 271
Write in overburning mode: NO (enabled: CD)

12:50:59 PM #12 Text 0 File DlgWaitCD.cpp, Line 2316
Recorder: MAD DOG MD-16XDVD9A4, Media type: DVD-R
Disc Manufacturer: TTH02 -
Disc Application Code: 64, Disc Physical Code: 193

12:50:59 PM #13 Text 0 File DlgWaitCD.cpp, Line 433
>>> Protocol of DlgWaitCD activities: <<<
=========================================

12:50:59 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 830
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2286128 (2286128) = #2286128/508:1.53
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286128 blocks [MAD DOG MD-16XDVD9A4]
--------------------------------------------------------------

12:50:59 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1043
Prepare recorder [MAD DOG MD-16XDVD9A4] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681990144, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2286128 | lead-out | 1 | 0x41 | 0x00

12:50:59 PM #16 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started

12:50:59 PM #17 Text 0 File Burncd.cpp, Line 4040
Cache writing successful.

12:50:59 PM #18 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed

12:50:59 PM #19 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 4x (5,540 KB/s)

12:50:59 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2609
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

12:50:59 PM #21 Text 0 File DVDR.cpp, Line 2356
Recording mode: Sequential Recording Mode

12:50:59 PM #22 Text 0 File Mmc.cpp, Line 21206
Set BUFE: Buffer underrun protection -> ON

12:50:59 PM #23 Text 0 File DVDR.cpp, Line 2502
Start write address at LBA 0
DVD high compatibility mode: Yes

12:50:59 PM #24 Text 0 File Cdrdrv.cpp, Line 8442
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 5
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

12:51:02 PM #25 Text 0 File Cdrdrv.cpp, Line 1287
12:51:02.078 - MAD DOG MD-16XDVD9A4\H4 T0 : Queue again later

12:51:09 PM #26 SCSI -500 File Cdrdrv.cpp, Line 1435
SCSI Exec, HA 4, TA 0, LUN 0, buffer 0x0BD70000
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02

12:51:10 PM #27 Text 0 File Cdrdrv.cpp, Line 1287
12:51:10.093 - MAD DOG MD-16XDVD9A4\H4 T0 : Queue again later

12:51:12 PM #28 SCSI -500 File Cdrdrv.cpp, Line 1435
SCSI Exec, HA 4, TA 0, LUN 0, buffer 0x0C420800
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02

12:51:12 PM #29 Text 0 File Mmc.cpp, Line 18838
Writer-Buffer for MAD DOG MD-16XDVD9A4\H4 T0 reduced to 32768Bytes

12:51:13 PM #30 SCSI -1114 File Cdrdrv.cpp, Line 1435
SCSI Exec, HA 4, TA 0, LUN 0, buffer 0x0C420800
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x10 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0A
0x00 0x00 0x00 0x00 0x29 0x00

12:51:13 PM #31 CDR -1114 File Writer.cpp, Line 311
Reset occurred

12:51:13 PM #32 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

12:51:13 PM #33 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader

12:51:13 PM #34 Text 0 File DVDR.cpp, Line 2765
EndDAO: Last written address was -1

12:51:13 PM #35 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 4x (5,540 KB/s)


Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 9/14/2005 11:17:44 AM (Prassi/Veritas driver for win 2K)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)


Thanks in advance.
RavenX is offline   Reply With Quote
Old 14 Nov 2005, 04:28 AM   #2
Super Moderator
 
Chewy's Avatar
 
Join Date: Nov 2003
Location: millenium falcon
Posts: 18,971
Default

"CdRomPeripheral : SCSIVAX DVD/CD-ROM 2.7a Vax347s Port 2 ID 0 DMA: Off"

scuzzi optical drive?

and you're missing this driver,
"File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 03/08/2004 22:59:44 (Adapter driver for rec)"
Chewy is offline   Reply With Quote
Old 14 Nov 2005, 04:58 AM   #3
Junior Member
Junior Member
 
Join Date: Nov 2005
Posts: 18
Default

ok I just uninstalled alcohol 120, and tried to burn scarface again and the same thing happened, reset error. But this time It shows the "File 'Drivers\atapi.sys': Ver=5.1.2600.2180" at the bottom of the log.


Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'D:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 9:35:32 AM
Nero Version: 6.6.0.8 (Nero Express)
Recorder: <MAD DOG MD-16XDVD9A4> Version: 1.F1 - HA 3 TA 0 - 6.6.0.8
Adapter driver: <> HA 3
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <TOSHIBA DVD-ROM SD-M1302>Version: 1006 - HA 1 TA 1 - 6.6.0.8
=== Scsi-Device-Map ===
CdRomPeripheral : TDK CDRW121032 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : TOSHIBA DVD-ROM SD-M1302 atapi Port 1 ID 1 DMA: On
DiskPeripheral : WDC WD2000JD-00GBB0 02.0 viamraid Port 2 ID 0 DMA: Off

=== CDRom-Device-Map ===
TDK CDRW121032 E: CDRom0
TOSHIBA DVD-ROM SD-M1302 F: CDRom1
MAD DOG MD-16XDVD9A4 G: CDRom2
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1022MB (1047280kB)
Free physical memory: 624MB (639304kB)
Memory in use : 38 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

13.11.2005
UDF/ISO compilation
1:50:36 PM #1 Phase 112 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation started

1:50:36 PM #2 Phase 114 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation completed (no file modified)

1:50:36 PM #3 Text 0 File Isodoc.cpp, Line 6172
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet :FALSE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE

1:50:36 PM #4 Phase 111 File dlgbrnst.cpp, Line 1832
DVD-Video files sorted

1:50:37 PM #5 Text 0 File Reader.cpp, Line 127
Reader running

1:50:37 PM #6 Text 0 File Writer.cpp, Line 122
Writer MAD DOG MD-16XDVD9A4 running

1:50:37 PM #7 ISO9660GEN -11 File geniso.cpp, Line 3293
First writeable address = 0 (0x00000000)

1:50:37 PM #8 ISO9660GEN -11 File geniso.cpp, Line 3293
First writeable address = 0 (0x00000000)

1:50:37 PM #9 Text 0 File Burncd.cpp, Line 3153
Turn on Disc-At-Once, using DVD media

1:50:37 PM #10 Text 0 File DlgWaitCD.cpp, Line 259
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286127 (508:01.52, 4465MB)

1:50:37 PM #11 Text 0 File DlgWaitCD.cpp, Line 271
Write in overburning mode: NO (enabled: CD)

1:50:37 PM #12 Text 0 File DlgWaitCD.cpp, Line 2316
Recorder: MAD DOG MD-16XDVD9A4, Media type: DVD-R
Disc Manufacturer: TTH02 -
Disc Application Code: 64, Disc Physical Code: 193

1:50:37 PM #13 Text 0 File DlgWaitCD.cpp, Line 433
>>> Protocol of DlgWaitCD activities: <<<
=========================================

1:50:37 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 830
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2286128 (2286128) = #2286128/508:1.53
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286128 blocks [MAD DOG MD-16XDVD9A4]
--------------------------------------------------------------

1:50:37 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1043
Prepare recorder [MAD DOG MD-16XDVD9A4] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681990144, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2286128 | lead-out | 1 | 0x41 | 0x00

1:50:37 PM #16 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started

1:50:37 PM #17 Text 0 File Burncd.cpp, Line 4040
Cache writing successful.

1:50:37 PM #18 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed

1:50:37 PM #19 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 16x (22,160 KB/s)

1:50:37 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2609
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

1:50:37 PM #21 Text 0 File DVDR.cpp, Line 2356
Recording mode: Sequential Recording Mode

1:50:37 PM #22 Text 0 File Mmc.cpp, Line 21206
Set BUFE: Buffer underrun protection -> ON

1:50:37 PM #23 Text 0 File DVDR.cpp, Line 2502
Start write address at LBA 0
DVD high compatibility mode: Yes

1:50:37 PM #24 Text 0 File Cdrdrv.cpp, Line 8442
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 5
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

1:50:40 PM #25 Text 0 File Cdrdrv.cpp, Line 1287
13:50:40.218 - MAD DOG MD-16XDVD9A4\H3 T0 : Queue again later

1:50:46 PM #26 SCSI -500 File Cdrdrv.cpp, Line 1435
SCSI Exec, HA 3, TA 0, LUN 0, buffer 0x0BD60000
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02

1:50:47 PM #27 Text 0 File Cdrdrv.cpp, Line 1287
13:50:47.031 - MAD DOG MD-16XDVD9A4\H3 T0 : Queue again later

1:50:47 PM #28 SCSI -500 File Cdrdrv.cpp, Line 1435
SCSI Exec, HA 3, TA 0, LUN 0, buffer 0x0C410800
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02

1:50:47 PM #29 Text 0 File Mmc.cpp, Line 18838
Writer-Buffer for MAD DOG MD-16XDVD9A4\H3 T0 reduced to 32768Bytes

1:50:48 PM #30 SCSI -1114 File Cdrdrv.cpp, Line 1435
SCSI Exec, HA 3, TA 0, LUN 0, buffer 0x0C410800
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x10 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0A
0x00 0x00 0x00 0x00 0x29 0x00

1:50:48 PM #31 CDR -1114 File Writer.cpp, Line 311
Reset occurred

1:50:48 PM #32 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

1:50:48 PM #33 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader

1:50:48 PM #34 Text 0 File DVDR.cpp, Line 2765
EndDAO: Last written address was -1

1:50:48 PM #35 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 16x (22,160 KB/s)


Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 9/14/2005 11:17:44 AM (Prassi/Veritas driver for win 2K)
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 8/3/2004 9:59:42 PM (Adapter driver for src)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
RavenX is offline   Reply With Quote
Old 14 Nov 2005, 05:36 AM   #4
Super Moderator
 
Chewy's Avatar
 
Join Date: Nov 2003
Location: millenium falcon
Posts: 18,971
Default

Nero and aspi may already be hosed, you are using an external drive
and we can't tell anything unless you burn at 4x.
usb2 does well no faster than that
Your drive and it's firmware are excellent tho.
Media looks topnotch also.
Nero needs updating.
Chewy is offline   Reply With Quote
Old 14 Nov 2005, 05:37 AM   #5
Junior Member
Junior Member
 
Join Date: Nov 2005
Posts: 18
Default

thanks for the fast reply. what I will do, is do a burn again in 4x and post the log.
RavenX is offline   Reply With Quote
Old 14 Nov 2005, 05:56 AM   #6
Junior Member
Junior Member
 
Join Date: Nov 2005
Posts: 18
Default

I went back and tried it at 4x and it work perfectly. So why is it that I can burn at 4x speed but not at 16x speed? Both the burner and the blank dvd support those speeds. Also, thanks again for your help.
RavenX is offline   Reply With Quote
Old 14 Nov 2005, 07:04 AM   #7
Super Moderator
 
Chewy's Avatar
 
Join Date: Nov 2003
Location: millenium falcon
Posts: 18,971
Default

The usb interface (all the stuff at each end, not just the cable) will
theoretically handle 480Mb/s. I can leap tall buildings in a single bound.
Bend steel, faster than a speeding bullet. Now for reality, the best I have
seen usb2 on a healthy computer is 12MB/s, just about 8x dvd burning speed.
With your burner inside the computer(on a 33MB/s interface),8x would be an optimum speed with grade a media.
Chewy is offline   Reply With Quote
Old 14 Nov 2005, 02:22 PM   #8
Junior Member
Junior Member
 
Join Date: Nov 2005
Posts: 18
Default

Not sure why this is happening.....

I used Magic DVD ripper to rip Black Hawk Down and then dvd shrink to compress it and nero 6 to burn at 4x and Im still gettin a reset error.

Here is the log.

Windows XP 5.1
IA32
WinAspi: File 'Wnaspi32.dll': Ver=4.60 (1021), size=45056 bytes, created 9/10/1999 12:06:00 PM
ahead WinASPI: File 'D:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
Nero Version: 6.6.0.18
Internal Version: 6, 6, 0, 18e
(Nero Express)
Recorder: <MAD DOG MD-16XDVD9A4> Version: 1.F1 - HA 3 TA 0 - 6.6.0.18
Adapter driver: <> HA 3
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <TOSHIBA DVD-ROM SD-M1302>Version: 1006 - HA 1 TA 1 - 6.6.0.18
=== Scsi-Device-Map ===
CdRomPeripheral : TDK CDRW121032 atapi Port 1 ID 0 DMA: On
CdRomPeripheral : TOSHIBA DVD-ROM SD-M1302 atapi Port 1 ID 1 DMA: On
DiskPeripheral : WDC WD2000JD-00GBB0 02.0 viamraid Port 2 ID 0 DMA: Off

=== CDRom-Device-Map ===
TDK CDRW121032 E: CDRom0
TOSHIBA DVD-ROM SD-M1302 F: CDRom1
MAD DOG MD-16XDVD9A4 G: CDRom2
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1022MB (1047280kB)
Free physical memory: 602MB (616504kB)
Memory in use : 41 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

13.11.2005
UDF/ISO compilation
11:46:16 PM #1 Phase 112 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation started

11:46:16 PM #2 Phase 114 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation completed (no file modified)

11:46:16 PM #3 Text 0 File Isodoc.cpp, Line 6359
UDF document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
UDF Mode : UDF/ISO bridge
UDF Revision : 1.02
UDF Partition Type : physical
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet :FALSE
Allow pathdepth more than 8 directories : FALSE
Allow more than 255 characters in path : FALSE
Write ISO9660 ;1 file extensions : TRUE

11:46:16 PM #4 Phase 111 File dlgbrnst.cpp, Line 1832
DVD-Video files sorted

11:46:16 PM #5 Text 0 File Reader.cpp, Line 127
Reader running

11:46:16 PM #6 Text 0 File Writer.cpp, Line 122
Writer MAD DOG MD-16XDVD9A4 running

11:46:16 PM #7 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)

11:46:16 PM #8 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)

11:46:16 PM #9 Text 0 File Burncd.cpp, Line 3233
Turn on Disc-At-Once, using DVD media

11:46:17 PM #10 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2286127 (508:01.52, 4465MB)

11:46:17 PM #11 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO (enabled: CD)

11:46:17 PM #12 Text 0 File DlgWaitCD.cpp, Line 2483
Recorder: MAD DOG MD-16XDVD9A4, Media type: DVD-R
Disc Manufacturer: TTH02 -
Disc Application Code: 64, Disc Physical Code: 193

11:46:17 PM #13 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================

11:46:17 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 838
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2286128 (2286128) = #2286128/508:1.53
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286128 blocks [MAD DOG MD-16XDVD9A4]
--------------------------------------------------------------

11:46:17 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [MAD DOG MD-16XDVD9A4] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681990144, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2286128 | lead-out | 1 | 0x41 | 0x00

11:46:17 PM #16 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started

11:46:17 PM #17 Text 0 File Burncd.cpp, Line 4122
Cache writing successful.

11:46:17 PM #18 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed

11:46:17 PM #19 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 4x (5,540 KB/s)

11:46:17 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2661
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

11:46:17 PM #21 Text 0 File DVDR.cpp, Line 2571
Recording mode: Sequential Recording Mode

11:46:17 PM #22 Text 0 File Mmc.cpp, Line 21774
Set BUFE: Buffer underrun protection -> ON

11:46:17 PM #23 Text 0 File DVDR.cpp, Line 2726
Start write address at LBA 0
DVD high compatibility mode: Yes

11:46:17 PM #24 Text 0 File Cdrdrv.cpp, Line 8892
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 2.1 (33)
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26127F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 2FE10 h
Start sector number of the next Border-In: 2FFA0 h
Media Specific [16..63]:
00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!....
00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

11:46:19 PM #25 Text 0 File Cdrdrv.cpp, Line 1288
23:46:19.515 - MAD DOG MD-16XDVD9A4\H3 T0 : Queue again later

11:46:20 PM #26 SCSI -500 File Cdrdrv.cpp, Line 1436
SCSI Exec, HA 3, TA 0, LUN 0, buffer 0x0B650000
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02

11:46:20 PM #27 Text 0 File Cdrdrv.cpp, Line 1288
23:46:20.812 - MAD DOG MD-16XDVD9A4\H3 T0 : Queue again later

11:46:21 PM #28 SCSI -500 File Cdrdrv.cpp, Line 1436
SCSI Exec, HA 3, TA 0, LUN 0, buffer 0x0BD01400
Status: 0x02 (0x03, SCSI_ABORTED)
HA-Status 0x10 (0x0A, SCSI_HASTAT_REQUEST_SENSE_FAILED)
TA-Status 0x00 (0x00, OK)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x26
Sense Qual: 0x02
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x26 0x02

11:46:21 PM #29 Text 0 File Mmc.cpp, Line 19440
Writer-Buffer for MAD DOG MD-16XDVD9A4\H3 T0 reduced to 32768Bytes

11:46:21 PM #30 SCSI -1114 File Cdrdrv.cpp, Line 1436
SCSI Exec, HA 3, TA 0, LUN 0, buffer 0x0BD01400
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x06 (KEY_UNIT_ATTENTION)
Sense Code: 0x29
Sense Qual: 0x00
CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x10 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0A
0x00 0x00 0x00 0x00 0x29 0x00

11:46:21 PM #31 CDR -1114 File Writer.cpp, Line 311
Reset occurred

11:46:21 PM #32 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

11:46:22 PM #33 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader

11:46:22 PM #34 Text 0 File DVDR.cpp, Line 2969
EndDAO: Last written address was -1

11:46:22 PM #35 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 4x (5,540 KB/s)


Existing drivers:
File 'Drivers\ASPI32.SYS': Ver=4.60 (1021), size=25244 bytes, created 9/10/1999 12:06:00 PM
File 'Drivers\PXHELP20.SYS': Ver=2.02.62a, size=20016 bytes, created 9/14/2005 11:17:44 AM (Prassi/Veritas driver for win 2K)
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 8/3/2004 9:59:42 PM (Adapter driver for src)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)


The only change I made since getting scarface to work was updating nero. Before I had 6.6.0.8, now I have 6.6.0.18.

I also used Nero info tool to check my ASPI and it was working fine for nero ASPI but not the system. So I went ahead and used ForceASPI v1.7 and followed the directions, but still getting the reset error.

Last edited by RavenX; 14 Nov 2005 at 02:54 PM
RavenX is offline   Reply With Quote
Old 14 Nov 2005, 03:16 PM   #9
Not a god of digital video
 
blutach's Avatar
 
Join Date: Oct 2004
Location: is everything!
Posts: 24,628
Default

Turn your DMA on for your hard drive.

Read and implement the Golden Rules of Burning.

Regards
__________________
Les

Essential progs - [PgcEdit] [VobBlanker] [MenuShrink] [IfoEdit] [Muxman] [DVD Remake Pro] [DVD Rebuilder] [BeSweet] [Media Player Classic] [DVDSubEdit] [ImgBurn]

Media and Burning - [Golden Rules of Burning] [Media quality] [Fix your DMA] [Update your Firmware] [What's my Media ID Code?] [How to test your disc]
[What's bitsetting?] [Burn dual layer disks safely] [Why not to burn with Ner0] [Interpret Ner0's burn errors] [Got bad playback?] [Burner/Media compatibility]

Cool Techniques - [2COOL's guides] [Clean your DVD] [Join a flipper] [Split into 2 DVDs] [Save heaps of Mb] [How to mock strip] [Cool Insert Clips]

Real useful info - [FAQ INDEX] [Compression explained] [Logical Remapping of Enabled Streams] [DVD-Replica] [Fantastic info on DVDs]


You should only use genuine Verbatim or Taiyo Yuden media. Many thanks to www.pcx.com.au for their supply and great service.

Explore the sites and the programs - there's a gold mine of information in them

Don't forget to play the Digital Digest Quiz!!! (Click here)

blutach is offline   Reply With Quote
Old 14 Nov 2005, 03:25 PM   #10
Junior Member
Junior Member
 
Join Date: Nov 2005
Posts: 18
Default

thanks for the fast reply, I went into device manager and clicked on my hard drive and went to properties. I did not see an "advance settings" tab to change the dma settings. Is there some other way to enable dma for my hard drive? btw. my hard drive is a serial ata.

Last edited by RavenX; 14 Nov 2005 at 03:33 PM
RavenX is offline   Reply With Quote
Old 14 Nov 2005, 03:47 PM   #11
Not a god of digital video
 
blutach's Avatar
 
Join Date: Oct 2004
Location: is everything!
Posts: 24,628
Default

You do it thru the IDE controllers - see the DMA FAQ - link in my signature.

Regards
blutach is offline   Reply With Quote
Old 14 Nov 2005, 04:27 PM   #12
Junior Member
Junior Member
 
Join Date: Nov 2005
Posts: 18
Default

I have read the dma faq topic here FAQ: What's all this about DMA? and also read the post by Cynthia. The post says that I need an ATAPI driver for my sata hard drive. I noticed the current driver I have is a SCSI which does not let me change DMA. I did a search for Esdi_506.pdr and found out it does not support Windows XP. Not sure where to go from here and if I am even doing this right?
RavenX is offline   Reply With Quote
Old 14 Nov 2005, 04:34 PM   #13
Super Moderator
 
Chewy's Avatar
 
Join Date: Nov 2003
Location: millenium falcon
Posts: 18,971
Default

raven;
like I said earlier,
"Nero and aspi may already be hosed,"

I am afraid you will have to run killaspi and nero clean tools and reinstall,
not really up to speed on aspi, all I know is it's caused me a bunch of grief
in the past, when I started using XP and got rid of dinosaur programs
that were written for dos, the problem went away.

try running kill aspi, nero uses it's own aspi layer, xp native alternative works fine,
Chewy is offline   Reply With Quote
Old 14 Nov 2005, 04:36 PM   #14
Super Moderator
 
Chewy's Avatar
 
Join Date: Nov 2003
Location: millenium falcon
Posts: 18,971
Default

Quote:
Originally Posted by RavenX
I have read the dma faq topic here FAQ: What's all this about DMA? and also read the post by Cynthia. The post says that I need an ATAPI driver for my sata hard drive. I noticed the current driver I have is a SCSI which does not let me change DMA. I did a search for Esdi_506.pdr and found out it does not support Windows XP. Not sure where to go from here and if I am even doing this right?

leave your scuzzi(serial controller) alone, it's fine.
Chewy is offline   Reply With Quote
Old 14 Nov 2005, 04:37 PM   #15
Junior Member
Junior Member
 
Join Date: Nov 2005
Posts: 18
Default

Sorry for all this hassle, just trying to get my burner to work. Ok I will run killaspi, then uninstall nero and use nero clean tools, then reinstall. that sound right?
RavenX is offline   Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT +10. The time now is 04:45 AM.

Kirsch designed by Andrew & Austin


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
Copyright © 1999 - 2011 Digital Digest

Visit DivXLand   Visit dvdloc8.com