IMG Burn burning problem

[lemonyx]

Got the PC back together after the blue screen, IMG Burn will not burn with the BenQ 1655. The buffer fills but the device buffer does not fill up. It'll just sit there and do nothing. Used to burn within 30secs or less.

It'll burn with the NEC 3550, but I use that to "read" from.

BenQ burn log:

I 13:41:48 ImgBurn Version 2.3.2.0 started!
I 13:41:48 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 2)
I 13:41:48 Total Physical Memory: 2,095,532 KB - Available: 1,429,024 KB
I 13:41:49 Initialising SPTI...
I 13:41:49 Searching for SCSI / ATAPI devices...
I 13:41:49 Found 2 DVD±RWs!
I 13:43:24 Operation Started!
I 13:43:24 Source File: H:\HEMAN_VOLUME_2_D3.ISO
I 13:43:24 Source File Sectors: 2,211,607 (MODE1/2048)
I 13:43:24 Source File Size: 4,529,371,136 bytes
I 13:43:24 Source File Volume Identifier: HEMAN_VOLUME_2_D3
I 13:43:24 Source File Implementation Identifier: DVD Shrink
I 13:43:24 Source File File System(s): ISO9660, UDF (1.02)
I 13:43:24 Destination Device: [2:0:0] BENQ DVD LS DW1655 BCIB (Q (ATA)
I 13:43:24 Destination Media Type: DVD-R (Disc ID: TYG02) (Speeds: 2.4x, 4x, 8x)
I 13:43:24 Destination Media Sectors: 2,298,496
I 13:43:24 Write Mode: DVD
I 13:43:24 Write Type: DAO
I 13:43:24 Write Speed: MAX
I 13:43:24 Link Size: Auto
I 13:43:24 Test Mode: No
I 13:43:24 BURN-Proof: Enabled
I 13:43:24 Filling Buffer... (40 MB)
I 13:43:25 Writing LeadIn...
I 13:48:59 Abort Request Acknowledged

Help!

[lemonyx]

Hee's the NEC burn log:

I 14:16:23 ImgBurn Version 2.3.2.0 started!
I 14:16:23 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 2)
I 14:16:23 Total Physical Memory: 2,095,532 KB - Available: 1,546,956 KB
I 14:16:23 Initialising SPTI...
I 14:16:23 Searching for SCSI / ATAPI devices...
I 14:16:23 Found 2 DVD±RWs!
I 14:16:41 Operation Started!
I 14:16:41 Source File: H:\HEMAN_VOLUME_2_D3.ISO
I 14:16:41 Source File Sectors: 2,211,607 (MODE1/2048)
I 14:16:41 Source File Size: 4,529,371,136 bytes
I 14:16:41 Source File Volume Identifier: HEMAN_VOLUME_2_D3
I 14:16:41 Source File Implementation Identifier: DVD Shrink
I 14:16:41 Source File File System(s): ISO9660, UDF (1.02)
I 14:16:41 Destination Device: [0:0:0] _NEC DVD_RW ND-3550A 1.Y5 (N (SCSI)
I 14:16:41 Destination Media Type: DVD-R (Disc ID: TYG02) (Speeds: 2x, 4x, 6x, 8x, 12x)
I 14:16:41 Destination Media Sectors: 2,297,888
I 14:16:41 Write Mode: DVD
I 14:16:41 Write Type: DAO
I 14:16:41 Write Speed: MAX
I 14:16:41 Link Size: Auto
I 14:16:41 Test Mode: No
I 14:16:41 BURN-Proof: Enabled
I 14:16:41 Filling Buffer... (40 MB)
I 14:16:42 Writing LeadIn...
I 14:17:30 Writing Image... (LBA: 0 - 2211606)
I 14:24:20 Synchronising Cache...
I 14:24:38 Image MD5: Nero Serial Removed79d1
I 14:24:38 Operation Successfully Completed! - Duration: 00:07:57
I 14:24:38 Average Write Rate: 10,814 KB/s (7.8x) - Maximum Write Rate: 14,572 KB/s (10.5x)

[Chewy]

you haven't changed any cables around have you?

nec shows scuzzi the benq ata?

moved to imgburn forum for luk to look at

[lemonyx]

Changed everything around. Or it would'n load or find a HD.

Have boot HD on the pri ide, the BenQ is on the sec ide and the NEC is on a PCI controller card with the second HD.

Sometimes the QSuite will find the BenQ and sometimes not.

[Chewy]

maybe it's a driver issue then?

what happens when you switch the burner's cables to other controllers?

[lemonyx]

The drivers are the std generic Windows XP drivers. I switched the cables around and still nothing. I moved the jumper back to Master from cable select and switched the cables back and still nothing.

Both DVD's r/w are on the IDE sockets pri and sec and the HD's are on a PCi controller card. I can put the NEC on any position and it'll work but not the BenQ.

I tried reading a DVD from the BenQ and it was doing 65kd's and not the usual 42-4400kb's like the Nec.

[Chewy]

promise chip that controls sata and pata? same for the intel chipset

FastTrak 378 don’t support ATAPI device

[lemonyx]

Sorry, Chewy - do I need to unintsall the driver?? And how do I do that??

TIA

[Chewy]

I don't know what the benq has been hooked to, it may be dead for all I know

did you install the IAA driver?

[lemonyx]

What is the IAA driver? And where do find it?

[Chewy]

IntelApplicationAccelerator

if installed it should show in add/remove, try uninstalling or updating it??

might want to check the benq in another computer