Problem To Backup My Original DVD'S To A 4.7GB Blank DVD Disc

[Dimortal]

Hey There People,
I Have A Small Problem.
The Problem Is That I Have A Pioneer A03 DVD-RW Burner But.
I Can't Seem To Copy Any DVD Movies To A Standard 4.7GB
Disc...I Know The Original Is Copyrighted And Too Large To Fit
On The Standard Disk.But I Would Like To Know Of Any
Possible Way To Break Down The Original DVD To 4.7 or Lower.
I Know How To Rip The Dvd. But Don't How To Take And
Seperate The VOB'S To An Audio*.*ts & Video*.* Folder In
The Asbect Of 4.7 Or Lower In Size....
If Any One Can Assist Or Help Me In Anyway I Would Be
Most Grateful...
Thanking You In Advance
... DIMORTAL ...
Dimortal

[tazmax]

Hay
Here's how I BACK UP MY DVD collection
On DVD Digest
get DVD Decrypter It seams to be the Best

On divx digest
get FlaskMPEG It also seams to be the best
get TMPGEnc

And to Burn get
MyDVD 3.5
cause it will let you put 3.5 hours of VCD
on a DVD
I also have the same burner as you
if you e-mail me I can
give you some hints as to how to get the best
quality
tborden@usa.com
I've backed up a lot of dvd's
and I'm learning some of the tricks
I've thrown away a lot of
5$ and up DVD's
I can also send you instructions on the above software
I got off the net
they work great !!!

[vic102482]

Well you cuold try what I tried,

Get a tv capture card, hook your dvd player up to it, capture the movie to your harddrive and use the included software to burn it back to a dvd. I have tyhe PIONEER A03 and I have more than 10 successful copies

[tazmax]

VHS

Hay
I also back up my VHS collection on DVD's
but you won't get the quality of Video
and I've had voice to video sink. troubles
the capture to my hard drive is OK
but when I burn them they look like
a dubbed movie
But some times it works great
If you can tell me how to aline the video and Voice
It sure would help
But like I said on the computer it is OK

[vic102482]

well

Whenever you have sync problems like voice or jumpy video you can best elieve that there is a problem either your CPU is maxed out or is not being utilized correctly, the best way to resovle that is to frist test and see if you capture at a lower resolution does the jumpynesss and stuff go away? If yes then you have solved your problem rioght there, also you need a clean harddrive DEFRAGGIN IS VERY IMPORTANT very, you are driving your car at 100 mp you dont want to keep swerving out of the way of oncoming traffic you need a clear path and also check out if your HDD is 5400 or 7200 that makes a big diffrence also with your ATA cause ATA33 on the HDD aint gonna cut it 66 or higher when you are playing with the big boys of MPEG

[tazmax]

Thanks

Sounds like you might be able to help

My system
P4 1.7
512 meg ram at 266
7200 rpm 60 Gig HDD WESTERN DIG
ATI Radon 8500 Video card 64 DDR
soundblaster gammer sound card
Windows 98 se
I just found out the front side buss on the board is just 133
I'm looking to replace it soon
It's a Shuttle AV40
With Ultra DMA 100 controler

I do defrag before I burn
I even defrag before I make a Image

also I even turn off the clock when I burn
my system is at 98 % when I start
cause I've ran config editor and shut down all
thinks running in the back ground
after starting MyDVD it's at 94%
and the only thing that's wrong is the out of syn.
with voice and video and only
on a VHS that I've captured
and the Image is OK it's only when I burn

But not when I burn from a copied DVD

just the VHS

and It only does it sometimes and I can't
figure out what is the Key

If you have ANY Ideas PLEASE send them

I do all my burning on a DVD-RW FIRST

Thank you for your Help

[Deepa DVD]

Hello there!
Are you bringing seperate video and a seperate audio file into your DVD Authoring Program? If yes, you are probally using 44.1 khZ audio. You need to convert your audio file to 48 khZ so it will stay in sync with the video.
I hope this was the solution to your problem!

[vic102482]

yes that is true

Some dvd players wont even recogzine 44k audio and ULEAD refuses to burn with that kind of sample rate, go with the 48

[nicktran111467]

Why don't you use IFOedit to break the ripped DVD files (VOB) into standard 4.7 DVD-Rs, create in image file and use DVD Decrypter to burn back to DVD-R disk?