Tweet
HELP! Cant set sound using FLASK0594
I rip the dvd using smart ripper, i then use the flask program to convert them into mpeg4 using the below guide.
~~~~~~~~~~~~~~~~~
Open FlaskMpeg. If you get an error you will have to run 'register DivX' from the DivX file you downloaded.
Once opened choose english and then 'lets start'. Now click file and locate the file you ripped with smart ripper.
Make sure MPEG video track 0xE0 is highlighted and the audio should be 0x80, then click flask it!
Now click options>global project options.
choose width as 640 and height as 480. Time base should be 25 for UK and 24 for US films ( this should be chosen for you).
Click Audio tab at top and make sure Decode audio is ticked.
Click files and choose where you want the compressed version of your DVD to be sent.
Click general and under miscellaneous you can choose to shutdown your computer after
Click options>output format options. Under video click select codec and choose DivX MPEG4 low motion then click configure. In the data rate option change to 700ish.(or use the calculator, the higher this is the better the quality but if too much over 700 it may not fit a single CD). Change the crispness slide bar to 75. Change the key frame to 1. click OK and ok again.
Now click the Audio Codec and change the format to MPEG 3 and attributes to 96kbs, then click ok, and ok again.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
when i set the video codec to DivX MPEG4 and change the settings, when i leave and go back to it, the settings are still the same, (another words they have saved). When i set the sound to MPEG 3 and attributes to 96kbs and exit, i return to the sound option and it has gone back to its default format of PCM with attributes of 48KHz, 16bit, stereo 187kb/sec. (another words it will not save my required setting.
The dvd conversion works fine in both picture and sound, but because it will not save my settings, the file size i wish to obtain by using a bit rate calculator always means the file size is always smaller than i require?
Can you help me set the stereo setting to MPEG 3 and attributes to 96kbs???
I rip the dvd using smart ripper, i then use the flask program to convert them into mpeg4 using the below guide.
~~~~~~~~~~~~~~~~~
Open FlaskMpeg. If you get an error you will have to run 'register DivX' from the DivX file you downloaded.
Once opened choose english and then 'lets start'. Now click file and locate the file you ripped with smart ripper.
Make sure MPEG video track 0xE0 is highlighted and the audio should be 0x80, then click flask it!
Now click options>global project options.
choose width as 640 and height as 480. Time base should be 25 for UK and 24 for US films ( this should be chosen for you).
Click Audio tab at top and make sure Decode audio is ticked.
Click files and choose where you want the compressed version of your DVD to be sent.
Click general and under miscellaneous you can choose to shutdown your computer after
Click options>output format options. Under video click select codec and choose DivX MPEG4 low motion then click configure. In the data rate option change to 700ish.(or use the calculator, the higher this is the better the quality but if too much over 700 it may not fit a single CD). Change the crispness slide bar to 75. Change the key frame to 1. click OK and ok again.
Now click the Audio Codec and change the format to MPEG 3 and attributes to 96kbs, then click ok, and ok again.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
when i set the video codec to DivX MPEG4 and change the settings, when i leave and go back to it, the settings are still the same, (another words they have saved). When i set the sound to MPEG 3 and attributes to 96kbs and exit, i return to the sound option and it has gone back to its default format of PCM with attributes of 48KHz, 16bit, stereo 187kb/sec. (another words it will not save my required setting.
The dvd conversion works fine in both picture and sound, but because it will not save my settings, the file size i wish to obtain by using a bit rate calculator always means the file size is always smaller than i require?
Can you help me set the stereo setting to MPEG 3 and attributes to 96kbs???
Comment